|
|
DIEHARD TXA2D
Meets or exceeds the performance requirements of SAE 100R2AT, AS 3791 100R2AT, BCS 174, DIN 20022-2SN,
EN 853 Type 2SN, ISO 1436 Types R2AT & 2SN.
Third Party approvals: ABS, DNV, GL, LR, MED, USCG (click to view).
|
|
Recommended For:
High pressure hydraulic oil lines in applications where the
outside cover of the hose is subjected to abrasion that may
cause premature failure of standard hoses.
The working pressures of DIEHARD AGGRESSOR exceed the
requirements of EN 853 Type 2SN & SAE 100R2AT by at least 30%, and all sizes exceed the working pressure requirements of SAE 100R9.
The very high abrasion resistant properties of the cover, combined with the high working pressures and excellent
impulse life when tested to EN 853 Type 2SN/SAE 100R2AT
test conditions result in, increased service life and minimise equipment downtime. Ideal for high pressure use that requires a smaller outside diameter (except -20 size), lighter weight, and more flexibility than spiral hose.
Tube:
Black, oil resistant synthetic rubber. (Nitrile).
Reinforcement:
Two braids of high tensile steel wire.
Cover:
Black, extra abrasion resistant and oil resistant rubber.
“FRAS” Flame Resistant and Anti-Static.
The weight loss of the cover under ISO 6945 method of test for abrasion resistance is less than 10% (less than 0,05 g) of that allowed by DIN 20022-2SN and EN 853 Type 2SN.
Highly visible layline branding for easy and permanent
identification.
No skiving required with T200 & T700 Series BITELOK Crimp
Couplings and L Series Field Attachable Couplings. |
Temperature Range:
From -40°C to +100°C (-40°F to +212°F).
For water, emulsions etc. click to view
Working Pressure:
Maximum working perssures are based on 4:1 safety factor (minimum burst to maximum working pressure).
Flame Resistance:
Complies with Flame Resistant and Electrical Resistance (Anti-Static) requirements of Australian Standard AS 2660 and Methods of Test AS 1180.10B and 13A.
Meets Flame Resistant Designation “U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
Couplings:
BITELOK NON-SKIVE ONE-PIECE CRIMP
T200 Series (sizes -8 to -20) click to view
T700 Series (sizes -8 to -20) click to view
Assembly Instructions click to view
FIELD ATTACHABLE NON-SKIVE
L Series (sizes -8 to -20) click to view
Assembly Instructions click to view |
|
| PART NO | HOSE SIZE ID | MAX. DYNAMIC
WORKING PRESSURE | MIN.
BURST PRESSURE |
| | DN | INCH | DASH | BAR | PSI | BAR | PSI |
TXA28D | 12 | 1/2 | -08 | 375 | 5440 | 1500 | 21760 |
TXA210D | 16 | 5/8 | -10 | 350 | 5100 | 1400 | 20400 |
TXA212D | 19 | 3/4 | -12 | 313 | 4530 | 1252 | 18120 |
TXA216D | 25 | 1 | -16 | 225 | 3250 | 900 | 13040 |
TXA220D | 31 | 1.1/4 | -20 | 175 | 2540 | 700 | 10160 |
| PART NO | MINIMUM
BEND RADIUS | AVERAGE
WEIGHT | NOMINAL
HOSE OD | FIELD ATTACHABLE
L SERIES | BITELOK
ONE PIECE CRIMP |
| | MM | INCH | KGS/M | LBS/FT | MM | INCH | INSERT | FERRULE | NON-SKIVE |
TXA28D | 178 | 7.0 | 0,72 | 0.48 | 22,0 | 0.87 | 600 SERIES | L00-08 | T200 | T700 |
TXA210D | 200 | 8.0 | 0,87 | 0.58 | 25,2 | 0.99 | 600 SERIES | L00-10 | T200 | T700 |
TXA212D | 240 | 9.5 | 1,11 | 0.75 | 29,1 | 1.15 | 600 SERIES | L00-12 | T200 | T700 |
TXA216D | 300 | 12.0 | 1,50 | 1.01 | 37,7 | 1.48 | 600 SERIES | L00-16 | T200 | T700 |
TXA220D | 419 | 16.5 | 2,28 | 1.53 | 48,0 | 1.89 | 600 SERIES | L00-20 | T200 | T700 |
Contact RYCO Hydraulics for Crimp Diameter and Mark Length for BITELOK Couplings.
|
|
|