|
|
SURVIVOR RQP1
Meets or exceeds the performance requirements of SAE 100R1AT, AS 3791 100R1AT, DIN 20022-1SN, EN 853 Type 1SN, ISO 1436 Types R1AT & 1SN.
Third Party approvals: ABS, DNV, GL, LR, MED, USCG (click to view).
|
|
Recommended For:
High pressure hydraulic oil applications where pressure or temperature requirements exceed the performance requirements of SAE 100R1AT and DIN 20022-1SN, or where resistance to phosphate ester** fluid is required.
May be used with compressed air if cover of hose is perforated (pin-pricked) and additional Safety Devices are used.
Tube:
Black, synthetic rubber, specifically compounded for temperature resistance and multi fluid resistance.
Reinforcement:
One braid of high tensile steel wire.
Cover:
Blue, oil resistant and abrasion resistant, synthetic rubber.
No skiving required with T200 & T700 Series BITELOK Crimp Couplings and K Series Field Attachable Couplings*.
Temperature Range:
From -40°C to +150°C (-40°F to +302°F).
For water, water/oil emulsions, diesel fuels, glycol, air, and some phosphate esters** click here
**Not suitable for use with aerospace type phosphate esters such as Monsanto Skydrol 500B, Stauffer Aero-Safe 2300W and Chevron Hy-jet IV. |
Working Pressure:
Maximum working pressures are based on 4:1 safety factor (minimum burst to maximum working pressure).
Flame Resistance:
Meets Flame Resistant Designation “U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration. Complies with Flame Resistant requirements of Australian Standard AS 2660 and Method of Test AS 1180.10B.
Couplings:
BITELOK NON-SKIVE ONE-PIECE CRIMP
T200 Series (sizes -4 to -16) click to view
T700 Series (sizes -6 to -16) click to view
Assembly Instructions click to view
FIELD ATTACHABLE NON-SKIVE*
K Series (sizes -4 to -16) click to view
Assembly Instructions click to view |
|
| PART NO | HOSE SIZE ID | MAX. DYNAMIC
WORKING PRESSURE | MIN.
BURST PRESSURE |
| | DN | INCH | DASH | BAR | PSI | BAR | PSI |
RQP14 | 6 | 1/4 | -04 | 225 | 3250 | 900 | 13000 |
RQP15 | 8 | 5/16 | -05 | 215 | 3120 | 860 | 12480 |
RQP16 | 10 | 3/8 | -06 | 180 | 2600 | 720 | 10400 |
RQP18 | 12 | 1/2 | -08 | 160 | 2300 | 640 | 9200 |
RQP110 | 16 | 5/8 | -10 | 130 | 1900 | 520 | 7600 |
RQP112 | 19 | 3/4 | -12 | 120 | 1740 | 480 | 6960 |
RQP116 | 25 | 1 | -16 | 90 | 1300 | 360 | 5200 |
| PART NO | MINIMUM
BEND RADIUS | AVERAGE
WEIGHT | NOMINAL
HOSE OD | FIELD ATTACHABLE
K SERIES | BITELOK
ONE PIECE CRIMP |
| | MM | INCH | KGS/M | LBS/FT | MM | INCH | INSERT | FERRULE | NON-SKIVE |
RQP14 | 100 | 4.0 | 0,24 | 0.16 | 13,4 | 0.53 | 600 SERIES | K00-04 | T200 | |
RQP15 | 114 | 4.5 | 0,27 | 0.18 | 15,0 | 0.59 | | | T200 | |
RQP16 | 127 | 5.0 | 0,34 | 0.23 | 17,4 | 0.69 | 600 SERIES | K00-06 | T200 | T700 |
RQP18 | 178 | 7.0 | 0,44 | 0.30 | 20,5 | 0.81 | 600 SERIES | K00-08 | T200 | T700 |
RQP110 | 200 | 8.0 | 0,51 | 0.34 | 23,7 | 0.93 | 600 SERIES | K00-10 | T200 | T700 |
RQP112 | 240 | 9.5 | 0,64 | 0.43 | 27,6 | 1.09 | 600 SERIES | K00-12 | T200 | T700 |
RQP116 | 300 | 12.0 | 0,98 | 0.66 | 35,7 | 1.41 | 600 SERIES | K00-16 | T200 | T700 |
|
*Field Attachable Couplings should not
be used on RQP1 Hose at maximum working pressure when temperature exceeds
121°C (250°F). Field Attachable Couplings may be used on RQP1 Hose at over
121°C but at reduced working pressure. Contact RYCO for more information. |
Contact RYCO Hydraulics for Crimp Diameter and
Mark Length for BITELOK Couplings. |
|
|
|