SURVIVOR RQP2

Meets or exceeds the performance requirements of SAE 100R2AT, AS 3791 100R2AT, DIN 20022-2SN, EN 853 Type 2SN, ISO 1436 Types R2AT & 2SN. Third Party approvals: ABS, DNV, GL, LR, MED, USCG (click to view).

Recommended For: High pressure hydraulic oil applications where pressure or temperature requirements exceed the performance requirements of SAE 100R2AT and DIN 20022-2SN, or where resistance to phosphate ester** fluid is required. May be used with compressed air if cover of hose is perforated (pin-pricked) and additional Safety Devices are used. Tube: Black, synthetic rubber, specifically compounded for temperature resistance and multi fluid resistance. Reinforcement: Two braids of high tensile steel wire. Cover: Blue, oil resistant and abrasion resistant synthetic rubber. No skiving required with T200 & T700 Series BITELOK Crimp Couplings and L Series Field Attachable Couplings*. Temperature Range: From -40°C to +150°C (-40°F to +302°F). For water, water/oil emulsions, diesel fuels, glycol, air, and some phosphate esters** click to view **Not suitable for use with aerospace type phosphate esters such as Monsanto Skydrol 500B, Stauffer Aero-Safe 2300W and Chevron Hy-jet IV.

Working Pressure: Maximum working pressures are based on 4:1 safety factor (minimum burst to maximum working pressure). Flame Resistance: Meets Flame Resistant Designation “U.S. MSHA” of the US Department of Labor, Mine Safety & Health Administration. Complies with Flame Resistant requirements of Australian Standard AS 2660 & Method of Test AS 1180.10B. Couplings: BITELOK NON-SKIVE ONE-PIECE CRIMP T200 Series (sizes -4 to -20) click to view T700 Series (sizes -6 to -32) click to view Assembly Instructions click to view FIELD ATTACHABLE NON-SKIVE* L Series (sizes -4 to -20) click to view Assembly Instructions click to view FIELD ATTACHABLE SKIVE* B Series*** (sizes -24 and -32) click to view Assembly Instructions click to view

Hose Working Pressures 1 BAR = 14.5 PSI  1 MPA = 10 BAR
PART NO	HOSE SIZE ID			MAX. DYNAMIC WORKING PRESSURE		MIN. BURST PRESSURE
	DN	INCH	DASH	BAR	PSI	BAR	PSI
RQP24	6	1/4	-04	400	5800	1600	23200
RQP25	8	5/16	-05	350	5100	1400	20400
RQP26	10	3/8	-06	350	5100	1400	20400
RQP28	12	1/2	-08	300	4350	1200	17400
RQP210	16	5/8	-10	250	3600	1000	14500
RQP212	19	3/4	-12	215	3100	860	12400
RQP216	25	1	-16	167	2400	670	9600
RQP220	31	1.1/4	-20	150	2175	600	8700
RQP224	38	1.1/2	-24	100	1450	400	5800
RQP232	51	2	-32	90	1300	360	5200

Hose Dimensions							Matched Couplings
PART NO	MINIMUM BEND RADIUS		AVERAGE WEIGHT		NOMINAL HOSE OD		B SERIES SKIVE LENGTH	FIELD ATTACHABLE L (&B) SERIES		BITELOK ONE PIECE CRIMP
	MM	INCH	KGS/M	LBS/FT	MM	INCH	MM	INSERT	FERRULE	NON-SKIVE
RQP24	100	4.0	0,39	0.26	15,0	0.59		600 SERIES	L00-04	T200
RQP25	114	4.5	0,45	0.30	16,6	0.65				T200
RQP26	127	5.0	0,53	0.36	19,0	0.75		600 SERIES	L00-06	T200	T700
RQP28	178	7.0	0,65	0.44	22,0	0.87		600 SERIES	L00-08	T200	T700
RQP210	200	8.0	0,77	0.52	25,2	0.99		600 SERIES	L00-10	T200	T700
RQP212	240	9.5	0,93	0.62	29,1	1.15		600 SERIES	L00-12	T200	T700
RQP216	300	12.0	1,38	0.93	37,7	1.48		600 SERIES	L00-16	T200	T700
RQP220	419	16.5	2,03	1.36	48,0	1.89		600 SERIES	L00-20	T200	T700
RQP224	500	20.0	2,30	1.55	54,4	2.14	53	600 SERIES	***B00-24		T700
RQP232	600	24.0	3,16	2.12	67,3	2.65	58	600 SERIES	***B00-32		T700

*Field Attachable Couplings should not be used on RQP2 Hose at maximum working pressure when temperature exceeds 121°C (250°F). Field Attachable Couplings may be used on RQP2 Hose at over 121°C but at reduced working pressure. Contact RYCO Hydraulics for more information.

***When using B Series Field Attachable Couplings on RQP2 Series Hose, cover of hose must be skived at ends. Contact RYCO Hydraulics for Crimp Diameter and Mark Length for BITELOK Couplings.