INTRODUCTION
COUPLINGS
FILTERS
hOse
ACCESSORIES
ADAPTORS
TECHNICAL
79
CONNECTING PARTNERSHIPS
h4000a – aveNgeR
IsObaRIC spIRal hOse
paRT NO hOse sIZe
NOmINal
hOse ID
NOmINal
hOse OD
maxImUm
wORKINg
pRessURe
mINImUm
bURsT
pRessURe
mINImUm
beND
RaDIUs
aveRage
weIghT
COUplINg seRIes
ONe pIeCe
Hose
dn dash mm inch mm inch bar psi bar psi mm inch kg/m lb/ft
non-skive
H4006a
10
-06 9,5 3/8 19,3 0.76 280 4100 1120 16400 62 2.4 0,61 0.41
T7000
H4008a
12
-08 12,7 1/2 22,7 0.89 280 4100 1120 16400 90 3.5 0,78 0.52
T7000
H4010a
16
-10 15,9 5/8 24,9 0.98 280 4100 1120 16400 100
3.9 0,76 0.51
T7000
H4012a
19
-12 19,1 3/4 30,0 1.18 280 4100 1120 16400 120 4.7 1,13 0.76
T7000
H4016a
25
-16 25,4 1 36,9 1.45 280 4100 1120 16400 150
5.9 1,60 1.08
T7000
H4020a
31
-20 31,8 1.1/4 44,0 1.73 280 4100 1120 16400 210
8.3 2,07 1.39
T7000
H4024a
38
-24 38,1 1.1/2 50,8 2.00 280 4100 1120 16400 330 13.0 2,65 1.78
T7000
H4032a
51
-32 50,8 2 66,4 2.61 280 4100 1120 16400 400 15.8 4,73 3.18
T7000
Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
recommended for:
High pressure hydraulic oil lines. Constant pressure
(Isobaric) 280 bar / 4100 psi in all sizes. Small bend radius is
an advantage in installations.
Performance:
Meets or Exceeds the Performance Requirements of:
EN 856 Type R12, EN 856 Type 4SP (size DN25, -16),
ISO 18752-DC, SAE 100R12.
Tube:
Black, oil resistant synthetic rubber.
reinforcemenT:
Four (-06 to -24 size) and six (-32 size) alternating layers of
spiralled high tensile steel wire.
cover:
avenger™
Black, oil and abrasion resistant synthetic
rubber. Flame Resistant & MSHA compliant. Highly visible
layline branding for easy and permanent identification.
No skiving required with T7000 Series BITELOK Crimp
Couplings.
feaTures:
Tested to
1 million impulse cycles
at up to 1/2 SAE 100R12
Minimum Bend Radius. Constant pressure 280 bar / 4100 psi
in all sizes for easy system design and hose selection.
Small bend radius is an advantage in installations.
msHa - flame resisTance:
avenger™
complies with Flame Resistant requirements
of Australian Standard AS 2660 and Method of Test
AS 1180.10B. Meets Flame Resistant Designation
“U.S. MSHA” of the US Department of Labor, Mine Safety
and Health Administration.
TemPeraTure range:
-40°C to +121°C, -40°F to +250°F.
For water, emulsions etc. see page 57.
Working Pressure:
Maximum working pressures are based on 4:1 safety factor
(maximum working pressure to minimum burst pressure).
THird ParTy aPProvals:
ABS, DNV, GL, LR, MED and USCG.
couPlings:
biTelok non-skive one-Piece crimP
T7000 series
(sizes -06 to -32) pages 217 to 233.
Assembly Instructions page 498.
h4000a
ISObARIC SPIRAL HOSE
280 bAR / 4100 PSI
mIllION CyCle
ISObARIC SPIRAL
1...,71,72,73,74,75,76,77,78,79,80 82,83,84,85,86,87,88,89,90,91,...544