Page 101 - 2019 PRODUCT TECHNICAL MANUAL - HYDRAULICS V4-8
P. 101

 BRAID
T1S
EXTREMELY ABRASION RESISTANT ONE WIRE BRAID HOSE
          RECOMMENDED FOR:
High pressure hydraulic oil lines.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: AS 3791 100R1AT, DIN 20022-1SN, EN 853 Type 1SN, ISO 1436 Types R1AT & 1SN, SAE 100R1AT.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
One braid of high tensile steel wire.
COVER:
SLIDER Black, oil and extremely abrasion resistant synthetic rubber sheathed with a layer of extremely abrasion
resistant polyethylene. Flame Resistant, MSHA compliant. Highly visible layline branding for easy and permanent identification. No skiving required with T2000 Series Crimp Couplings.
MSHA - FLAME RESISTANCE:
SLIDER complies with Flame Resistant requirements
of Australian Standard AS 2660 and Methods of Test
AS 1180.10B. Meets Flame Resistant Designation
“U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
TEMPERATURE RANGE:
From -40°C to +100°C (-40°F to +212°F). For water, emulsions etc. see page 58..
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
THIRD PARTY APPROVALS:
ABS, DNV-GL, LR, MED, USCG, GOST-R, BV, RINA, KR & MA-KA.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T2000 Series (sizes -03 to -32) pages 189 to 234. Assembly Instructions pages 480.
    T1S – SLIDER NON-SKIVE HOSE
PART NO
HOSE SIZE
NOMINAL HOSE ID
NOMINAL HOSE OD
MAXIMUM WORKING PRESSURE
MINIMUM BURST PRESSURE
MINIMUM BEND RADIUS
AVERAGE WEIGHT
COUPLING SERIES
ONE PIECE
  Hose DN Dash mm inch mm inch bar psi bar psi mm inch kg/m lb/ft NON-SKIVE
 T13S
5
-03
4,8
3/16
11,7
0.46
250
3600
1000
14500
35
1.4
0,19
0.13
 T2000
 T14S 6 -04 6,6 1/4 13,3 0.52 225 3250 900 13000 40 1.5 0,22 0.15 T16S 10 -06 9,8 3/8 17,3 0.68 180 2600 720 10400 50 2.0 0,31 0.21 T110S 16 -10 16,2 5/8 23,6 0.93 130 1900 520 7600 90 3.5 0,49 0.33 T116S 25 -16 25,4 1 35,5 1.40 90 1300 360 5200 140 5.5 0,90 0.60 T124S 38 -24 38,1 1.1/2 50,2 1.98 50 725 200 2900 250 9.8 1,45 0.97
Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
T2000 T2000 T2000 T2000 T2000
T15S
8
-05
8,2
5/16
14,9
0.59
215
3100
860
12400
50
2.0
0,25
0.17
T2000
T18S
12
-08
13,0
1/2
20,3
0.80
160
2300
640
9200
75
3.0
0,39
0.26
T2000
T112S
19
-12
19,1
3/4
27,6
1.09
105
1500
420
6000
110
4.3
0,62
0.42
T2000
T120S
31
-20
31,8
1.1/4
43,2
1.70
65
945
260
3780
210
8.3
1,21
0.81
T2000
T132S
 51
-32
50,8
2
63,6
2.50
40
580
160
2320
315
12.4
2,09
1.40
T2000
      HIGHER TECHCNOONLNOEGCYTEINQUGAPLASRGTNREARTSEHRIPPSERFORMANCE
99
TECHNICAL ADAPTORS COUPLINGS HOSE INTRODUCTION
   99   100   101   102   103