Page 104 - 2019 PRODUCT TECHNICAL MANUAL - HYDRAULICS V4-8
P. 104

 HOSE
BRAID
RECOMMENDED FOR:
High pressure hydraulic oil lines in applications where the outside cover of the hose is subjected to sliding abrasion that may cause premature failure of standard hoses.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: AS 3791 100R2AT, DIN 20022-2SN, EN 853 Type 2SN, ISO 1436 Type 2AT, SAE 100R2AT.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
Two braids of high tensile steel wire.
COVER:
SLIDER Black, oil and extremely abrasion resistant synthetic rubber sheathed with a layer of extremely abrasion
resistant polyethylene. Flame Resistant, MSHA compliant. Highly visible layline branding for easy and permanent identification. No skiving required with T2000 & T7000 Series Crimp Couplings.
MSHA - FLAME RESISTANCE:
SLIDER complies with Flame Resistant requirements
of Australian Standard AS 2660 and Methods of Test
AS 1180.10B. Meets Flame Resistant Designation
“U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
TEMPERATURE RANGE:
From -40°C to +100°C (-40°F to +212°F). For water, emulsions etc. see page 58.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
THIRD PARTY APPROVALS:
ABS, DNV-GL, LR, MED, USCG, GOST-R, BV, RINA, KR & MA-KA.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T2000 Series (sizes -04 to -32) pages 189 to 234. T7000 Series (sizes -05 to -32) pages 274 to 304. Assembly Instructions pages 480.
 T2S
EXTREMELY ABRASION RESISTANT TWO WIRE BRAID HOSE
        T2S – SLIDER NON-SKIVE HOSE
 PART NO
  HOSE SIZE
NOMINAL HOSE ID
NOMINAL HOSE OD
MAXIMUM WORKING PRESSURE
MINIMUM BURST PRESSURE
MINIMUM BEND RADIUS
AVERAGE WEIGHT
COUPLING SERIES
ONE PIECE
   Hose DN Dash mm inch mm inch bar psi bar psi mm inch kg/m lb/ft NON-SKIVE
 T24S
6
-04
6,6
1/4
14,9
0.59
420
6100
1680
24400
100
3.9
0,35
0.24
 T2000
  T25S 8 -05 8,2 5/16 16,5 0.65 350 5100
T28S 12 -08 13,0 1/2 21,9 0.86 350 5100
T212S 19 -12 19,1 3/4 29,1 1.15 215 3100
T220S 31 -20 31,8 1.1/4 47,6 1.87 140 2000
T232S 51 -32 50,8 2 66,8 2.63 90 1300 Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
1400 20400 114 4.5 0,42 0.28 T2000 1400 20400 178 7.0 0,65 0.44 T2000 860 12400 240 9.5 0,93 0.62 T2000 560 8000 420 16.5 1,97 1.33 T2000 360 5200 600 23.6 3,02 2.03 T2000
T7000 T7000 T7000 T7000
T26S
10
-06
9,8
3/8
18,9
0.74
350
5100
1400
20400
125
5.0
0,51
0.34
T2000
T7000
T210S
16
-10
16,2
5/8
25,1
0.99
250
3600
1000
14400
200
7.9
0,75
0.50
T2000
T7000
T216S
25
-16
25,4
1
37,5
1.48
175
2500
700
10000
300
11.8
1,30
0.87
T2000
T7000
T224S
38
-24
38,1
1.1/2
54,1
2.13
100
1450
400
5800
500
19.7
2,48
1.67
T2000
T7000
      102 RYCO QUALITY
   102   103   104   105   106