Page 108 - 2019 PRODUCT TECHNICAL MANUAL - HYDRAULICS V4-8

HOSE
SPIRAL
H12S
EXTREMELY ABRASION RESISTANT VERY HIGH PRESSURE MULTI-SPIRAL HOSE
RECOMMENDED FOR:
Very high pressure hydraulic oil lines, in applications where the outside cover of the hose is subject to sliding abrasion that may cause premature failure of standard hoses.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: AS 3791 100R12, EN 856 Type R12, EN 856 Type 4SP (-12 and above), ISO 3862 Type R12, SAE 100R12.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
Four alternating layers of spiralled high tensile steel wire.
COVER:
SLIDER Black, oil and extremely abrasion resistant synthetic rubber sheathed with a layer of extremely abrasion
resistant polyethylene. Flame Resistant, MSHA compliant. Highly visible layline branding for easy and permanent identification. No skiving required with T7000 Series Crimp Couplings.
FEATURES:
The extremely high abrasion resistant properties of the polyethylene sheathed cover, combined with the extra high working pressures and excellent impulse life, when tested to SAE 100R12 test conditions, result in increased service life and minimise equipment downtime.
MSHA - FLAME RESISTANCE:
SLIDER complies with Flame Resistant requirements
of Australian Standard AS 2660 and Methods of Test
AS 1180.10B. Meets Flame Resistant Designation
“U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
TEMPERATURE RANGE:
From -40°C to +121°C (-40°F to +250°F). For water, emulsions etc. see page 58.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
THIRD PARTY APPROVALS:
ABS, DNV-GL, LR, MED, USCG, GOST-R, BV, RINA and KR.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T7000 Series (sizes -06 to -32) pages 274 to 304. Assembly Instructions pages 480.
H12S – SLIDER SPIRAL HOSE
PART NO
HOSE SIZE
NOMINAL HOSE ID
NOMINAL HOSE OD
MAXIMUM WORKING PRESSURE
MINIMUM BURST PRESSURE
MINIMUM BEND RADIUS
AVERAGE WEIGHT
COUPLING SERIES
ONE PIECE
Hose DN Dash mm inch mm inch bar psi bar psi mm inch kg/m lb/ft NON-SKIVE
H1206S
10
-06
9,5
3/8
19,3
0.76
350
5100
1400
20400
125
5.0
0,61
0.41
T7000
H1208S 12 -08 12,7 1/2 22,7 0.89 350 5100 1400 20400 178 7.0 0,78 0.52
H1212S 19 -12 19,1 3/4 30,0 1.18 350 5100 1400 20400 240 9.5 1,21 0.81
H1220S 31 -20 31,8 1.1/4 45,7 1.80 275 4000 1100 16000 400 15.8 2,34 1.57
H1232S 51 -32 50,8 2 66,0 2.60 210 3050 840 12400 600 23.6 4,23 2.84 Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
T7000 T7000 T7000 T7000
H1210S
16
-10
15,9
5/8
26,2
1.03
350
5100
1400
20400
200
7.9
0,98
0.66
T7000
H1216S
25
-16
25,4
1
37,4
1.47
350
5100
1400
20400
300
11.8
1,84
1.24
T7000
H1224S
38
-24
38,1
1.1/2
53,0
2.09
255
3700
1020
14800
500
19.7
3,04
2.04
T7000
106 RYCO QUALITY