Page 112 - 2019 RYCO Product Technical Manual V1-8
P. 112

 HOSE
SPECIALTY AND HIGH TEMPERATURE
 TJ2D
EXTRA ABRASION RESISTANT FRAS
JACK HOSE
TWO WIRE BRAID
                                                    RECOMMENDED FOR:
Hydraulic Jack applications requiring a light weight, small outside diameter hose. The very high abrasion resistant properties of the DIEHARD cover extend the life of the hose when it is subjected to the abrasion that may cause the premature failure of standard hoses.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: Materials Handling Institute specification IJ 100 (July 1979) for hydraulic hose and assemblies used with jacking systems.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
Two braids of high tensile steel wire.
COVER:
DIEHARDTM Black, oil and extra abrasion resistant synthetic rubber. Flame Resistant, Anti-Static (FRAS) & MSHA compliant. Highly visible layline branding for easy and permanent identification. No skiving required with T2000 Series Crimp Couplings.
FRAS - FLAME RESISTANCE AND ANTI-STATIC:
DIEHARDTM complies with Flame Resistant and Electrical Resistance (Anti-Static) requirements of Australian Standard AS 2660 and Methods of Test AS 1180.10B and 13A.
Meets Flame Resistant Designation “U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
TEMPERATURE RANGE:
From -40°C to +49°C (-40°F to +120°F). For water, emulsions etc. see page 58.
WORKING PRESSURE:
Specification IJ 100 (July 1979) is based on 2:1 minimum burst to maximum working pressure safety factor and
is suitable for 700 bar/10,000 psi use in hydraulic jack applications ONLY.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T2000 Series (sizes -04 to -06) pages 188 to 233. Assembly Instructions pages 478.
TJ2D – DIEHARD JACK HOSE
                        PART NO
 HOSE SIZE
    NOMINAL HOSE ID
   NOMINAL HOSE OD
 MAXIMUM WORKING PRESSURE
 MINIMUM BURST PRESSURE
  MINIMUM BEND RADIUS
 AVERAGE WEIGHT
 COUPLING SERIES
 ONE PIECE
                 Hose
 DN
  Dash
 mm
 inch
 mm
 inch
 bar
 psi
bar
  psi
 mm
 inch
 kg/m
 lb/ft
 NON-SKIVE
  TJ24D
  6
   -04
  6,6
  1/4
  14.9
  0.59
  700
  10000
 1400
   20000
  100
  3.9
  0.35
  0.24
  T2000
 TJ26D
   10
    -06
   9,8
   3/8
   18.9
   0.74
   700
   10000
  1400
    20000
   130
   5.0
   0.51
   0.34
   T2000
    NOTE: Ensure rated Working Pressure of chosen End Style meets or exceeds the 700 bar/10,000 psi Maximum Working Pressure of TJ2D hose. For hydraulic jack applications, RYCO recommends the use of 3/8” NPTF Male Extended Couplings.
TJ24D: Part No. T2091-0406 One-Piece Crimp. Use of RYCO 750 Spring Guards at each end of the hose assembly is also recommended. TJ26D: Part No. T2091-0606 One-Piece Crimp. Use of a Bend Restrictor device at each end of the hose assembly is also recommended.
Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
       110 RYCO QUALITY









   110   111   112   113   114