Page 113 - RYCO Product Technical Manual 2019 V2-3
P. 113
SPECIALTY AND HIGH TEMPERATURE
RQP1
HIGH TEMPERATURE MULTI FLUID
ONE WIRE BRAID HOSE
RECOMMENDED FOR:
High pressure hydraulic oil applications where pressure or temperature requirements exceed the performance requirements of SAE 100R1AT and DIN 20022-1SN, or where resistance to phosphate ester** fluid is required. May be used with compressed air if cover of hose is perforated (pin- pricked) and additional Safety Devices are used.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: AS 3791 100R1AT, DIN 20022-1SN, EN 853 Type 1SN, ISO 1436 Types R1AT & 1SN, SAE 100R1AT.
TUBE:
Black, synthetic rubber, specifically compounded for temperature resistance and multi fluid resistance.
REINFORCEMENT:
One braid of high tensile steel wire.
COVER:
Survivor, blue, oil resistant and abrasion resistant synthetic rubber.
No skiving required with T2000 Series Crimp Couplings and K000 Series Field Attachable Couplings*.
MSHA - FLAME RESISTANCE:
Meets Flame Resistant Designation “U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration. Complies with Flame Resistant requirements of Australian Standard AS 2660 and Method of Test AS 1180.10B.
TEMPERATURE RANGE:
From -40°C to +150°C (-40°F to +302°F).
For water, water/oil emulsions, diesel fuels, glycol, air, and some phosphate esters** see page 58.
**Not suitable for use with aerospace type phosphate esters such as Monsanto Skydrol 500B, Stauffer Aero-Safe 2300W and Chevron Hy-jet IV.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
THIRD PARTY APPROVALS:
ABS, DNV-GL, LR, MED, USCG, GOST-R, BV, RINA and KR.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T2000 Series (sizes -04 to -16) pages 187 to 232. Assembly Instructions pages 478.
FIELD ATTACHABLE NON-SKIVE*
6000 SERIES insert (sizes -04 to -16) pages 250 to 271. K000 Series ferrule (sizes -04 to -16) page 353. Assembly Instructions page 476.
RQP1 – SURVIVOR NON-SKIVE HOSE
PART NO
HOSE SIZE
NOMINAL HOSE ID
NOMINAL HOSE OD
MAXIMUM WORKING PRESSURE
MINIMUM BURST PRESSURE
MINIMUM BEND RADIUS
AVERAGE WEIGHT
COUPLING SERIES
ONE PIECE
FIELD ATT
Hose
DN
Dash
mm
inch
mm
inch
bar
psi
bar
psi
mm
inch
kg/m
lb/ft
NON-SKIVE
RQP14
6
-04
6,6
1/4
13,4
0.53
225
3250
900
13000
100
4.0
0,24
0.16
T2000
6000 (K000)
RQP15
8
-05
8,2
5/16
15,0
0.59
215
3120
860
12500
114
4.5
0,27
0.18
T2000
RQP16
10
-06
9,8
3/8
17,4
0.69
180
2600
720
10400
125
5.0
0,34
0.23
T2000
6000 (K000)
RQP18
12
-08
13,0
1/2
20,5
0.81
160
2300
640
9300
178
7.0
0,44
0.30
T2000
6000 (K000)
RQP110
16
-10
16,2
5/8
23,7
0.93
130
1880
520
7540
200
8.0
0,51
0.34
T2000
6000 (K000)
RQP112
19
-12
19,1
3/4
27,6
1.09
120
1740
480
7000
240
9.5
0,64
0.43
T2000
6000 (K000)
RQP116 25 -16 25,4 1 35,7 1.41 90 1300 360 5200 300 12.0 0,98 0.66 T2000 6000 (K000)
* Field Attachable Couplings should not be used on RQP1 Hose at maximum working pressure when temperature exceeds 121˚C (250˚F). Field Attachable Couplings may be used on RQP1 Hose at over 121˚C but at reduced working pressure. Contact RYCO for more information.
Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
HIGHER TECHCNOONLNOEGCYTEINQUGAPLASRGTNREARTSEHRIPPSERFORMANCE 111
TECHNICAL ADAPTORS COUPLINGS HOSE INTRODUCTION