Page 116 - 2019 RYCO Product Technical Manual V1-8
P. 116

 HOSE
SPECIALTY AND HIGH TEMPERATURE
 RQP6
HIGH TEMPERATURE
ONE TEXTILE BRAID HOSE
                                        RECOMMENDED FOR:
Hydraulic oil lines, transmission oil cooler lines, glycol antifreeze solutions, water, diesel fuels and air.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of:
AS 3791 100R6, DIN 20021-1TE, ISO 4079 Type 1, SAE 100R6.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
One textile braid.
COVER:
Blue, oil resistant and abrasion resistant synthetic rubber.
MSHA - FLAME RESISTANCE:
Meets Flame Resistance Designation “U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration. Complies with Flame Resistant requirement of Australian Standard AS 2660 and Method of Test AS 1180.10B.
TEMPERATURE RANGE:
Petroleum base hydraulic oils & transmission oils:
-40°C to +135°C (-40°F to +275°F) constant, and up to +150°C (+302°F) intermittent (up to 10% of operating time). Air: -40°C to +100°C (-40°F to +212°F)
Diesel fuels: -40°C to +71°C (-40°F to +160°F).
For water, emulsions etc. see page 58.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
RQP6 Hose, and 8000 Series Push-On Fittings, are recommended for use in systems with Static Working Pressures (constant loads without pressure spikes) only. They are not recommended for vibration or pressure surge applications. RQP6 Hose should not be used at both maximum working pressure and maximum temperature simultaneously.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T4000 Series (Sizes -04 to -12) pages 234 to 250. Assembly Instructions pages 478.
8000 SERIES PUSH-ON
RQP6 Hose simply pushes on to 8000 Series Couplings, and for Static Working Pressures up to 50% of Maximum Static Working Pressures a clamp is not required. For diesel fuel and other potentially dangerous, or critical applications such as transmission oil cooler lines, and for Static Working Pressures above 50% of maximum; a clamp around the hose is required. Do not overtighten clamp as this will damage hose.
Factory crimped couplings are also available in some sizes.
 RQP6 – SURVIVOR HIGH TEMPERATURE PUSH ON HOSE
                                NOMINAL HOSE ID
   NOMINAL HOSE OD
MAXIMUM WORKING PRESSURE
  MINIMUM BURST PRESSURE
   MINIMUM BEND RADIUS
 VACUUM RATING
  AVERAGE WEIGHT
 COUPLING SERIES
PART NO
  HOSE SIZE
 ONE PC
 PUSH ON
            Hose
  DN
Dash
  mm
 inch
mm
  inch
 bar
psi
  bar
 psi
mm
  inch
 inHg
mmHg
  kg/m
 lb/ft
 NON-SKIVE
  RQP64
   6
 -04
   6,6
  1/4
 12,3
   0.48
  28
 410
   112
  1640
 65
   2.5
  710
 28
   0,12
  0.08
 T4000
   8000
 RQP65
  8
-05
  8,2
 5/16
13,9
  0.55
 28
410
  112
 1640
75
  3.0
 710
28
  0,14
 0.09
T4000
  8000
 RQP66
  10
-06
  9,8
 3/8
15,5
  0.61
 28
410
  112
 1640
75
  3.0
 635
25
  0,17
 0.11
T4000
  8000
 RQP68
  12
-08
  13,0
 1/2
19,0
  0.75
 28
410
  112
 1640
100
  4.0
 460
18
  0,22
 0.15
T4000
  8000
 RQP610
  16
-10
  16,2
 5/8
22,6
  0.89
 24
350
  96
 1400
125
  5.0
 380
15
  0,29
 0.19
T4000
  8000
 RQP612
    20
  -12
    19,1
   3/4
  25,8
    1.02
   21
  305
    84
   1220
  150
    6.0
   380
  15
    0,34
   0.23
  T4000
    8000
    Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
      114 RYCO QUALITY
   114   115   116   117   118