Page 140 - RYCO Hydraulics Technical Manual 2019
P. 140

 HOSE
THERMOPLASTIC
 TP7
SPIDERLINE R7 HOSE
                     RECOMMENDED FOR:
High pressure hydraulic oil lines; pilot lines; greasing and lubrication lines; and some pneumatic and water lines. Suitable for use with mineral, vegetable and most ester based hydraulic fluids. Suitable for use with some gases, fluids and chemicals. Cover is perforated (pin-pricked) for use with air and gases.
RYCO SPIDERLINE hose is lighter weight, has a more compact outside diameter and is less than half the minimum bend radius of wire braided rubber hose. Smooth inner tube for high flow rate; and smooth, easily cleaned cover.
The synthetic and aramid fibre reinforcement gives SPIDERLINE hose excellent corrosion and fatigue resistance plus low elongation at maximum dynamic working pressure.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: AS 3791 100R7, EN 855 TYPE R7, ISO 3949, SAE 100R7.
TUBE:
White, oil resistant seamless thermoplastic (Polyester).
REINFORCEMENT:
One or two braids of synthetic fibre.
COVER:
Black, oil and abrasion resistant thermoplastic (Polyurethane). Cover is perforated (pin-pricked).
TEMPERATURE RANGE:
From -40°C to +100°C (-40°F to +212°F). Air & Water +70 ˚C (+158 ˚F).
For water, emulsions etc. see page 58.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
TP000 Series (sizes -03 to -16) pages 304 to 316. Assembly Instructions pages 478.
TP7 – SPIDERLINE HOSE
                         PART NO
   HOSE SIZE
  NOMINAL HOSE ID
      NOMINAL HOSE OD
 MAXIMUM WORKING PRESSURE
 MINIMUM BURST PRESSURE
  MINIMUM BEND RADIUS
  AVERAGE WEIGHT
  COUPLING SERIES
  ONE PIECE
          Hose
  DN
 Dash
 mm
inch
  mm
 inch
 bar
 psi
 bar
 psi
mm
  inch
 kg/m
 lb/ft
 NON-SKIVE
  TP73
   5
  -03
  5,0
 3/16
   9,6
  0.38
  210
  3000
  840
  12000
 25
   1.0
  0,06
  0.04
  TP000
 TP74
  6
 -04
 6,5
1/4
  12,2
 0.48
 210
 3000
 840
 12000
35
  1.4
 0,10
 0.07
 TP000
 TP75
  8
 -05
 8,1
5/16
  14,3
 0.56
 190
 2700
 760
 10800
45
  1.8
 0,13
 0.09
 TP000
 TP76
  10
 -06
 9,7
3/8
  16,0
 0.63
 160
 2300
 640
 9200
55
  2.2
 0,15
 0.10
 TP000
 TP78
  12
 -08
 13,0
1/2
  20,3
 0.80
 140
 2000
 560
 8000
75
  3.0
 0,22
 0.15
 TP000
 TP712
  19
 -12
 19,5
3/4
  27,1
 1.07
 90
 1300
 360
 5200
140
  5.5
 0,34
 0.23
 TP000
 TP716
    25
   -16
   25,9
  1
    34,0
   1.34
   70
   1000
   280
   4000
  190
    7.5
   0,46
   0.31
   TP000
    Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
        138 HIGHER TECHNOLOGYRYECQOUAQLUSALGIRTEYATER PERFORMANCE
   138   139   140   141   142