Page 144 - 2019 RYCO Product Technical Manual V1-8
P. 144

 HOSE
THERMOPLASTIC
  TP7TN
ISOLATOR
R7 NON CONDUCTIVE TWIN HOSE
                                     RECOMMENDED FOR:
RYCO TP7TN ISOLATOR TWIN Hose consists of two TP7N Series Hoses of the same size, permanently joined together in a flat compact form that can be easily reeled onto payout and return reels on forklifts and cranes. It is also used for hydraulic powered hand tools, such as loppers and chain saws, and other applications requiring two hoses. TP7TN is used where electrical non-conductivity is required (for use
in applications where there is potential for contact with high voltage sources). Suitable for use with mineral, vegetable and most ester based hydraulic fluids. Heat and hydrolysis stabilised for use with water based hydraulic fluids up to +70°C (+158°F). Suitable for use with some gases, fluids and chemicals (contact RYCO Hydraulics Technical Department). Smooth inner tube for high flow rate; and smooth, easily cleaned cover. The polyester reinforcement gives TP7TN Hose excellent corrosion and fatigue resistance, and low elongation of ±2% at maximum dynamic working pressure.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: AS 3791 100R7, EN 855 TYPE R7, ISO 3949, SAE 100R7.
TUBE:
White, oil resistant seamless thermoplastic (Polyester).
REINFORCEMENT:
One or two braids of synthetic fibre.
COVER:
Orange, oil and abrasion resistant thermoplastic (Polyurethane). Cover is non-perforated.
FEATURES:
Meets non-conductivity requirements of SAE 100R7,
AS 3791 100R7, EN 855 Type 7 (maximum leakage does not exceed 50 μA when subjected to 75 kV/305 mm or 250 kV/m for 5 minutes). Incorrect storage and use, particularly that leading to oil or moisture entering the reinforcement, may adversely affect electrical properties.
TEMPERATURE RANGE:
From -40°C to +100°C (-40°F to +212°F). Air & Water +70 ˚C (+158 ˚F).
For water, emulsions etc. see page 58.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
TP000 Series (sizes -04 to -16) pages 304 to 316. Assembly Instructions pages 478.
               TP7TN – ISOLATOR NON-CONDUCTIVE TWIN HOSE
                       PART NO
HOSE SIZE
NOMINAL HOSE ID
inch
NOMINAL HOSE OD
MAXIMUM WORKING PRESSURE
MINIMUM BURST PRESSURE
MINIMUM BEND RADIUS
AVERAGE WEIGHT
COUPLING SERIES ONE PIECE
                                 Hose
DN
Dash
mm
mm
inch
bar
psi
bar
psi
mm
inch
kg/m
lb/ft
NON-SKIVE
                                 TP74TN
6
-04
6,5
1/4
12,2
0.48
210
3000
840
12000
35
1.4
0,20
0.13
TP000
                 TP76TN
10
-06
9,7
3/8
16,0
0.63
160
2300
640
9200
55
2.2
0,30
0.20
TP000
                 TP78TN
12
-08
13,0
1/2
20,3
0.80
140
2000
560
8000
75
3.0
0,44
0.30
TP000
                                  Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
       142 RYCO QUALITY
   142   143   144   145   146