Page 343 - 2019 PRODUCT TECHNICAL MANUAL - HYDRAULICS V4-8

V000 SERIES FIELD ATTACHABLE COUPLINGS
HOSE COMPATIBILITY FOR V000 SERIES
FOR RYCO SURVIVOR RQP5 AND TRUCKER T5 HOSE SERIES
RYCO V000 Series Ferrules follow the dash size of SURVIVOR RQP5 and TRUCKER T5 series hose. RQP5 and T5 Series are SAE 100R5 specification hose, and, accordingly the dash size is the corresponding tube size. SAE 100R5 hose internal diameters (nominal bores), unlike SAE 100R1, R2, etc, are smaller than their dash sizes. For example, T58 has nominal tube size of 1/2” and internal diameter of 13/32”, whereas T18 and T28 have nominal bore size of 1/2” and internal diameter of 1/2”. The reason for this difference is that T5 Series hoses are often used in applications where hose is connected to steel or copper tubing. The hose is sized so that its flow diameter is approximately the same as the flow diameter of the same nominal size tubing. Hence, the hose size relates to the nominal tube size.
RYCO V000 Series Ferrules are designed to match with RYCO 6000 Series Inserts.
RYCO 6000 Series Inserts have the same nominal sizing as their corresponding T1 and T2 Series Hose. Therefore, V000 Series Ferrules and matching 6000 Series Inserts have different ”dash” sizes. When matched together, V000 Series Couplings have the same dash size as the 6000 Series Inserts. See table below.
The chart below shows the relationship of Part Numbers for Ferrules, Inserts and Couplings for each size.
SURVIVOR RQP5
TRUCKER T5
HOSE (TUBE) DASH SIZE
HOSE ID INCH
V000 SERIES FERRULE
FERRULE DASH SIZE
6000 SERIES INSERTS
INSERT DASH SIZE
V000 SERIES COUPLINGS
COUPLING DASH SIZE
RQP54 RQP56 RQP510 RQP516 RQP524
T54 -04 3/16 T56 -06 5/16 T510 -10 1/2
T516 -16 7/8 T524 -24 1.3/8
V000-04 -04 V000-06 -06 V000-10 -10 V000-16 -16 V000-24 -24
6xxx-03 -03 Vxxx-03 -03 6xxx-05 -05 Vxxx-05 -05 6xxx-08 -08 Vxxx-08 -08 6xxx-14 -14 Vxxx-14 -14 6xxx-22 -22 Vxxx-22 -22
RQP55
T55
-05
1/4
V000-05
-05
6xxx-04
-04
Vxxx-04
-04
RQP58
T58
-08
13/32
V000-08
-08
6xxx-06
-06
Vxxx-06
-06
RQP512
T512
-12
5/8
V000-12
-12
6xxx-10
-10
Vxxx-10
-10
RQP520
T520
-20
1.1/8
V000-20
-20
6xxx-18
-18
Vxxx-18
-18
RQP532
T532
-32
1.13/16
V000-32
-32
6xxx-29
-29
Vxxx-29
-29
ADDITIONAL COUPLING END STYLES
Pages 235 to 251 show the T4000 Series Coupling End Styles As RYCO V000 Series Ferrules match with RYCO 6000 Series
that are also used with RQP5 and T5 hose. Inserts it is possible to use any RYCO 6000 Insert
from -03 to -10 listed in the 6000 Series Field Attachable Inserts with the matching Series Ferrule. Refer to RYCO for the availability of other 6000 Series Field Attachable Inserts.
CUT-OFF ALLOWANCE (CA) DIMENSIONS FOR FIELD ATTACHABLES
Due to differences in Ferrule design, many Cut-Off Allowance (CA) dimensions vary between each Ferrule Series for the same matched Insert/Hose size.
The Cut-Off Allowance (CA) dimensions published in “V Series Field Attachable Inserts” section allow for the Ferrule being eased back 5/8 of a turn after the hose has bottomed in the ferrule, as per “Field Attachable Assembly Instructions” (ease back between 1/2 and 3/4 of a turn).
The Cut-Off Allowance (CA) values for 6000 Series Inserts, published in the tables on pages 343 to 354 are for 6000 Series Inserts used with V000 Series Ferrules. If using V000 Series Ferrules with other matched 6000 Series Inserts listed on pages 357 to 387, contact RYCO Hydraulics Technical Department for the correct Cut-Off Allowance (CA).
If the hose assembly length is critical, when calculating the Cut Length of hose, you must also allow for an increase in length of hose when the coupling is attached, due to compression within the coupling; see page 356.
For further information about Hose Assemblies and Cut-Off Allowances (CA), see pages 467 to 473 of the Technical Section.
NOTE: Hose Compatibility for the V000 series can be found on page 325.
CONNECTING PARTNERSHIPS 341
TECHNICAL ADAPTORS COUPLINGS HOSE INTRODUCTION