Page 389 - RHAU-MKT RYCO Product Technical Manual 2018-12-14 v1-9
P. 389

 THREAD OR CONNECTOR TYPE
MIXTURE
 PAGE
    BSP
 BSPT/BSPP/BSPP O RING BSPT/JIC & BSPP O RING/JIC BSP/ORFS
BSP/SAE
BSP/UNO
  399 - 414
 NOTE: If an ADAPTOR is
available in both BSPT Male and BSPP O RING Male styles they are located close to each other.
 NPT & NPSM
 NPT/NPT
NPT/JIC
NPT/ORFS
NPT/SAE
NPT/UNO & NPSM/UNO
  415 - 421
 JIC
 JIC JIC/JIC JIC/ORFS JIC/UNO
  422 - 431
 JOINER
 TUBEWELD/TUBEWELD
  431
 METRIC*
 METRIC METRIC/BSPP O RING METRIC/JIC
  432 - 435
 ORFS
 ORFS ORFS/ORFS ORFS/UNO
  435 - 438
 SAE THREADS
 SAE SAE/SAE
  439 - 443
 SAE FLANGES*
 SAE FLANGE CLAMPS & CLAMP KITS SAE FLANGE PLUGS & TUBE WELD SAE FLANGE/JIC
SAE FLANGE/ORFS
SAE FLANGE BLOCKS
  Í444 - 448
 SWIVEL JOINTS
 BSP/BSP JIC/JIC
  449
 UNO (O RING BOSS)
 UNO UNO/UNO
  450
 MISCELLANEOUS
 O RINGS
PLASTIC CAP AND PLUGS TUBE BENDS
  451 - 457
 RYCOLOK & SUPERLOK*
 RYCOLOK & SUPERLOK BALL VALVES
  —
 RYCO WEO*
  RYCO WEO/RYCO WEO RYCO WEO/BSP
RYCO WEO/JIC
RYCO WEO/METRIC RYCO WEO/UNO
   458 - 460
    HIGHER TECHCNOONLNOEGCYTEINQUGAPLASRGTNREARTSEHRIPPSERFORMANCE
     CONTENTS
        *All adaptors with these thread or connector types are grouped together. The METRIC, SAE FLANGE, RYCOLOK, SUPERLOK or RYCO WEO end takes precedence. All METRIC adaptors, regardless of other end mixture, are in the METRIC group, and all SAE FLANGE adaptors are in SAE FLANGE group. Therefore a JIC/METRIC nipple will be found in METRIC Section not JIC Section; and an SAE FLANGE/BSP adaptor is in SAE FLANGE section not BSP section.
WORKING PRESSURES – STEEL ADAPTORS
Since many factors influence the pressure at which a hydraulic system will, or will not, perform satisfactorily, Maximum Working Pressures should be used as a guide only and not as a “standard” nor “specification” nor construed as a “guaranteed minimum.” Unless otherwise listed below, refer to pages 494 to 498 for Maximum Working Pressure guide. For further technical assistance contact RYCO or your RYCO distributor.
CAUTION: The Maximum Working Pressure of an Adaptor with a combination of Thread / End Styles and sizes is the Maximum Working Pressure of the least rated end.
NOTE: DROP LENGTHS (DL) AND CUT-OFF ALLOWANCES (CA):
Drop Lengths (DL) and Cut-off Allowances (CA) are in millimetres and are shown for reference only, and may vary according to manufacturing method, or due to design refinement.
387
TECHNICAL ADAPTORS COUPLINGS ADAPTORS INTRODUCTION


































   387   388   389   390   391