Page 477 - 2019 PRODUCT TECHNICAL MANUAL - HYDRAULICS V4-8

SAFETY GUIDE – MAXIMUM TEMPERATURE LIMITS
HOSE COVER
GROUP 1
GROUP 2
GROUP 3
GROUP 4
GROUP 5
ENERGY
E1, E2, EC1, EC2, DK1E, DK2E
DIEHARD
T3000D, T4000D, T5000D, T6000D, T1D, T2D, TXA2D, DF1D, DF2D, DK1D, DK2D, TJ2D, PL1D
H3000D, H4000D, H5000D. H6000D, C6000D, H12D, R4SPD, R4SHD, D4000D
SLIDER
T3000S, T4000S, T5000S, T6000S, T1S, T2S, DK1S, DK2S
H3000S, H4000S, H5000S. H6000S, C6000S, H12S
SURVIVOR
BT1 ***
D2B
RQP1, RQP2
ICEBREAKER
M2G, M1, RTH1, MP1
T3600C, H5000C, T2C
OTHER SERIES
SRF, SRX, M2, T5, T1F, PL1PV, CS1000, MS1000
RQP5, RQP6
TP7, TP7N, TP7T, TP7TN, TP8, TP8N, TP8T, TP8TN, TP3000, TPGL
MEDIA
TEMPERATURE LIMITS
GENERAL PURPOSE MINERAL PETROLEUM BASED HYDRAULIC OIL 1
-40°C to +100°C -40°F to +212°F
-40°C to +121°C -40°F to +250°F
-40°C to +150°C
-40°F to +302°F RQP6: -40° to +135°C -40°F to +275°F
-40°C to +95°C -40°F to +203°F
-60°C to +100°C -76°F to +212°F
WATER
0°C to +71°C +32°F to +160°F
0°C to +71°C +32°F to +160°F
0°C to +121°C +32°F +250°F
0°C to +70°C +32°F to +158°F
0°C to +71°C +32°F to +160°F
WATER IN MINERAL OIL 40% to 80% water
WATER/GLYCOL
PHOSPHATE ESTERS
PETROL GASOLINE
ENGINE LUBRICATING OIL, GEARBOX OIL
-40°C to +85°C -40°F to +185°F
-40°C to +85°C -40°F to +185°F
Not suitable
Contact RYCO
-40°C to +100°C -40°F to +212°F
-40°C to +85°C -40°F to +185°F
-40°C to +85°C -40°F to +185°F
Not suitable
Contact RYCO
-40°C to +100°C -40°F to +212°F
-40°C +121°C -40°F +250°F
-40°C to +121°C -40°F to +250°F
Not suitable
Contact RYCO
-40°C to +100°C -40°F to +212°F
-40°C to +70°C -40°F to +158°F
-40°C to +70°C -40°F to +158°F
40°C to +70°C -40°F to +158°F See note 2
Contact RYCO
-40°C to +95°C -40°F to +203°F
-60°C to +80°C -60°F to +176°F
-60°C to +80°C -60°F to +176°F
Not suitable
Contact RYCO
-60°C to +80°C -60°F to +176°F
MINERAL OIL IN WATER more than 80% water
-40°C to +85°C -40°F to+185°F
-40°C to +85°C -40°F to+185°F
-40°C to +121°C -40°F to +250°F
-40°C to +70°C -40°F to +158°F
-60°C to +80°C -60°F to +176°F
GLYCOL
-40°C to +85°C -40°F to +185°F
-40°C to +85°C -40°F to +185°F
-40°C to+85°C -40°F to +185°F
-40°C to+70°C -40°F to +158°F
-60°C to +80°C -60°F to +176°F
AIR 3
-40°C to +71°C (-40°F to +160°F)
-40°C to +71°C -40°F to +160°F see Note 3
-40°C to +121°C
-40°F to +250°F RQP6: -40°C to +100°C -40°F to +212°F See note 3
-40°C to +71°C -40°F to +160°F see Note 3
-60°C to +71°C -60°F to +160°F
DIESEL FUEL
PL1D: -40°C to +49°C -40°F to +160°F T5: -40°C to +71°C -40°F to +160°F OTHERS:
-40°C to +50°C -40°F to +122°F
-40°C to +50°C -40°F to +122°F
RQP1 and RQP2 -40°C to 100°C -40°F to +212°F RQP6: -40°C to +71°C -40°F to +160°F
-60°C to +71°C -60°F to +160°F
AUTOMATIC TRANSMISSION FLUID
-40°C to +100°C -40°F to +212°F
-40°C to +100°C -40°F to +212°F
-40°C to +100°C -40°F to +212°F
-40°C to +95°C -40°F to +203°F
-60°C to +80°C -60°F to +176°F
1 For highly refined and special purpose mineral based hydraulic oils (for example aviation hydraulic oils, MIL spec oils, etc), contact RYCO Technical Department.
2 Not suitable for use with aerospace type phosphate esters such as Monsanto Skydrol 500B, Stauffer Aero-Safe 2300W and Chevron Hy-jet IV.
3 For use with Air at pressures above 17,2 bar (250 psi), cover of hose must be perforated/pin-pricked (except RQP5 and T5), to allow air permeating through hose to escape without blistering the cover. Maximum working pressure of wire braid and spiral reinforced hose must be reduced by 30% (except for RQP1 and RQP2). Observe all State and Federal Safety Regulations.
CONNECTING PARTNERSHIPS
475
TECHNICAL ADAPTORS COUPLINGS HOSE INTRODUCTION