Page 65 - 2019 PRODUCT TECHNICAL MANUAL - HYDRAULICS V4-8

ISOBARIC BRAID
T3000S EXTREMELY ABRASION RESISTANT MSHA
COMPACT ISOBARIC HOSE
215 BAR / 3100 PSI
MILLION CYCLE
RECOMMENDED FOR:
High pressure hydraulic oil lines. Constant pressure (Isobaric) 215 bar / 3100 psi in all sizes. Small bend radius and compact dimensions are advantages in installations.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: ISO 18752-BC, SAE 100R17.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
One braid (-04 to -08 size) or two braids (-10 to -16 size) of high tensile steel wire.
COVER:
SLIDER Black, oil and extremely abrasion resistant synthetic rubber sheathed with a layer of extremely abrasion
resistant polyethylene. Flame Resistant, MSHA compliant. Highly visible layline branding for easy and permanent identification. No skiving required with T2000 Series Crimp Couplings.
FEATURES:
Tested to 1 million impulse cycles.
Constant pressure 215 bar / 3100 psi in all sizes for easy system design and hose selection. Small bend radius and compact dimensions are advantages in installations.
MSHA - FLAME RESISTANCE:
SLIDER complies with Flame Resistant requirements
of Australian Standard AS 2660 and Methods of Test
AS 1180.10B. Meets Flame Resistant Designation
“U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
TEMPERATURE RANGE:
-40°C to +100°C (-40°F to +212°F).
For water, emulsions etc. see page 58.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
THIRD PARTY APPROVALS:
ABS, DNV-GL, LR, MED, USCG, GOST-R, BV, RINA and KR.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T2000 Series (sizes -04 to -16) pages 189 to 234. Assembly Instructions pages 480.
T3000S – SLIDER COMPACT ISOBARIC HOSE
PART NO
HOSE SIZE
NOMINAL HOSE ID
NOMINAL HOSE OD
MAXIMUM WORKING PRESSURE
MINIMUM BURST PRESSURE
MINIMUM BEND RADIUS
AVERAGE WEIGHT
COUPLING SERIES
ONE PIECE
Hose DN Dash mm inch mm inch bar psi bar psi mm inch kg/m lb/ft NON-SKIVE T3005S 8 -05 8,2 5/16 14,4 0.57 245 3500 980 14000 40 1.6 0,23 0.15 T2000
T3004S
6
-04
6,6
1/4
11,8
0.46
245
3500
980
14000
38
1.5
0,16
0.11
T2000
T3006S
10
-06
9,8
3/8
15,6
0.61
215
3100
860
12400
65
2.6
0,26
0.18
T2000
T3008S 12 -08 13,0 1/2 18,7 0.74 215 3100 860 12400 90 3.6 0,36 0.24 T3012S 19 -12 19,1 3/4 27,6 1.09 215 3100 860 12400 120 4.7 0,78 0.52
Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
T2000 T2000
T3010S
16
-10
16,2
5/8
23,4
0.92
215
3100
860
12400
100
3.9
0,56
0.38
T2000
T3016S
25
-16
25,4
1
34,8
1.37
215
3100
860
12400
150
5.9
1,14
0.77
T2000
HIGHER TECHCNOONLNOEGCYTEINQUGAPLASRGTNREARTSEHRIPPSERFORMANCE
63
TECHNICAL ADAPTORS COUPLINGS HOSE INTRODUCTION