Page 69 - 2019 PRODUCT TECHNICAL MANUAL - HYDRAULICS V4-8

ISOBARIC BRAID
T4000D EXTRA ABRASION RESISTANT FRAS
COMPACT ISOBARIC HOSE 280 BAR / 4100 PSI
RECOMMENDED FOR:
High pressure hydraulic oil lines. Constant pressure (Isobaric) 280 bar / 4100 psi in all sizes. Small bend radius and compact dimensions are advantages in installations.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: ISO 18752-BC, SAE 100R19.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
One braid (-04 size) or two braids (-05 to -12 size) of high tensile wire.
COVER:
DIEHARDTM Black, oil and extra abrasion resistant synthetic rubber. Flame Resistant, Anti-Static (FRAS) & MSHA compliant. Highly visible layline branding for easy and permanent identification.
FEATURES:
Constant pressure 280 bar / 4100 psi in all sizes for easy system design and hose selection. Small bend radius and compact dimensions are advantages in installations.
FRAS - FLAME RESISTANCE AND ANTI-STATIC:
DIEHARDTM complies with Flame Resistant and Electrical Resistance (Anti-Static) requirements of Australian Standard AS 2660 and Methods of Test AS 1180.10B and 13A. Meets Flame Resistant Designation “U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
TEMPERATURE RANGE:
-40°C to +100°C (-40°F to +212°F).
For water, emulsions etc. see page 58.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
THIRD PARTY APPROVALS:
ABS, DNV-GL, LR, MED, USCG, GOST-R, BV, RINA and KR.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T2000 Series (sizes -04 to -12) pages 189 to 234. Assembly Instructions pages 480.
T4000D – DIEHARD COMPACT ISOBARIC HOSE
PART NO
HOSE SIZE
NOMINAL HOSE ID
NOMINAL HOSE OD
MAXIMUM WORKING PRESSURE
MINIMUM BURST PRESSURE
MINIMUM BEND RADIUS
AVERAGE WEIGHT
COUPLING SERIES
ONE PIECE
Hose DN Dash mm inch mm inch bar psi bar psi mm inch kg/m lb/ft NON-SKIVE T4005D 8 -05 8,2 5/16 15,6 0.61 280 4100 1120 16400 55 2.2 0,34 0.23 T2000
T4004D
6
-04
6,6
1/4
11,8
0.46
280
4100
1120
16400
50
2.0
0,17
0.12
T2000
T4006D
10
-06
9,8
3/8
16,6
0.65
280
4100
1120
16400
65
2.6
0,37
0.25
T2000
T4008D 12 -08 13,0 1/2 20,6 0.81 280 4100 1120 16400 90 3.6 0,51 0.34 T4012D 19 -12 19,1 3/4 28,4 1.12 280 4100 1120 16400 120 4.7 0,92 0.62
Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
T2000 T2000
T4010D
16
-10
16,2
5/8
23,4
0.92
280
4100
1120
16400
100
3.9
0,61
0.41
T2000
HIGHER TECHCNOONLNOEGCYTEINQUGAPLASRGTNREARTSEHRIPPSERFORMANCE
67
TECHNICAL ADAPTORS COUPLINGS HOSE INTRODUCTION