Page 75 - 2019 RYCO Product Technical Manual V1-8
P. 75

     ISOBARIC SPIRAL
 H3000D
EXTRA ABRASION RESISTANT FRAS
ISOBARIC SPIRAL HOSE
215 BAR / 3100 PSI
MILLION CYCLE
                                                                                                                                   RECOMMENDED FOR:
High pressure hydraulic oil lines. Constant pressure (Isobaric) 215 bar / 3100 psi in all sizes. Small bend radius is an advantage in installations.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: EN 856 Type R12, EN 856 Type 4SP, ISO 18752-DC, SAE 100R12.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
Four alternating layers of spiralled high tensile steel wire.
COVER:
DIEHARDTM Black, oil and extra abrasion resistant synthetic rubber. Flame Resistant, Anti-Static (FRAS) & MSHA compliant. Highly visible layline branding for easy and permanent identification. No skiving required with T7000 Series Crimp Couplings.
FEATURES:
Tested to 1 million impulse cycles at up to 1/2 SAE 100R12 Minimum Bend Radius. Constant pressure 215 bar / 3100 psi in all sizes for easy system design and hose selection.
Small bend radius is an advantage in installations.
FRAS - FLAME RESISTANCE AND ANTI-STATIC:
DIEHARDTM complies with Flame Resistant and Electrical Resistance (Anti-Static) requirements of Australian Standard AS 2660 and Methods of Test AS 1180.10B and 13A. Meets Flame Resistant Designation “U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
TEMPERATURE RANGE:
-40°C to +121°C (-40°F to +250°F).
For water, emulsions etc. see page 58.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
THIRD PARTY APPROVALS:
ABS, DNV-GL, LR, MED, USCG, GOST-R, BV, RINA and KR.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T2000 Series (sizes -20 to -32) pages 188 to 233. Assembly Instructions pages 478.
   H3000D – DIEHARD ISOBARIC SPIRAL HOSE
                        PART NO
 HOSE SIZE
    NOMINAL HOSE ID
   NOMINAL HOSE OD
 MAXIMUM WORKING PRESSURE
 MINIMUM BURST PRESSURE
  MINIMUM BEND RADIUS
 AVERAGE WEIGHT
 COUPLING SERIES
 ONE PIECE
          Hose
  DN
 Dash
mm
  inch
 mm
 inch
 bar
 psi
 bar
psi
  mm
 inch
 kg/m
 lb/ft
 NON-SKIVE
  H3020D
   31
  -20
 31,8
   1.1/4
  45,7
  1.80
  215
  3100
  860
 12400
   200
  7.9
  2,27
  1.53
  T7000
 H3024D
  38
 -24
38,1
  1.1/2
 50,3
 1.98
 215
 3100
 860
12400
  250
 9.8
 2,35
 1.58
 T7000
 H3032D
    51
   -32
  50,8
    2
   63,3
   2.49
   215
   3100
   860
  12400
    400
   15.8
   3,40
   2.28
   T7000
    Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
       CONNECTING PARTNERSHIPS 73
TECHNICAL ADAPTORS COUPLINGS HOSE INTRODUCTION
   73   74   75   76   77