Page 76 - 2019 RYCO Product Technical Manual V1-8
P. 76

 HOSE
ISOBARIC SPIRAL
  H3000S
EXTREMELY ABRASION RESISTANT MSHA
ISOBARIC SPIRAL HOSE
215 BAR / 3100 PSI
MILLION CYCLE
                                                                                                                                    RECOMMENDED FOR:
High pressure hydraulic oil lines. Constant pressure (Isobaric) 215 bar / 3100 psi in all sizes. Small bend radius is an advantage in installations.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: EN 856 Type R12, EN 856 Type 4SP, ISO 18752-DC, SAE 100R12.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
Four alternating layers of spiralled high tensile steel wire.
COVER:
SLIDER Black, oil and extremely abrasion resistant synthetic rubber sheathed with a layer of extremely abrasion
resistant polyethylene. Flame Resistant, MSHA compliant. Highly visible layline branding for easy and permanent identification. No skiving required with T7000 Series Crimp Couplings.
FEATURES:
Tested to 1 million impulse cycles at up to 1/2 SAE 100R12 Minimum Bend Radius. Constant pressure 215 bar / 3100 psi in all sizes for easy system design and hose selection.
Small bend radius is an advantage in installations.
MSHA - FLAME RESISTANCE:
SLIDER complies with Flame Resistant requirements
of Australian Standard AS 2660 and Methods of Test
AS 1180.10B. Meets Flame Resistant Designation
“U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
TEMPERATURE RANGE:
-40°C to +121°C (-40°F to +250°F).
For water, emulsions etc. see page 58.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
THIRD PARTY APPROVALS:
ABS, DNV-GL, LR, MED, USCG, GOST-R, BV, RINA and KR.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T7000 Series (sizes -20 to -32) pages 273 to 303. Assembly Instructions pages 478.
H3000S – SLIDER ISOBARIC SPIRAL HOSE
                        PART NO
  HOSE SIZE
  NOMINAL HOSE ID
    NOMINAL HOSE OD
 MAXIMUM WORKING PRESSURE
 MINIMUM BURST PRESSURE
  MINIMUM BEND RADIUS
 AVERAGE WEIGHT
 COUPLING SERIES
 ONE PIECE
          Hose
  DN
 Dash
 mm
inch
  mm
 inch
 bar
 psi
 bar
 psi
mm
  inch
 kg/m
 lb/ft
 NON-SKIVE
  H3020S
   31
  -20
  31,8
 1.1/4
   45,7
  1.80
  215
  3100
  860
  12400
 200
   7.9
  2,27
  1.53
  T7000
 H3024S
  38
 -24
 38,1
1.1/2
  50,3
 1.98
 215
 3100
 860
 12400
250
  9.8
 2,35
 1.58
 T7000
 H3032S
    51
   -32
   50,8
  2
    63,3
   2.49
   215
   3100
   860
   12400
  400
    15.8
   3,40
   2.28
   T7000
    Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
       74 RYCO QUALITY
   74   75   76   77   78