Page 77 - 2019 RYCO Product Technical Manual V1-8
P. 77

     ISOBARIC SPIRAL
H4000D
EXTRA ABRASION RESISTANT FRAS
ISOBARIC SPIRAL HOSE
280 BAR / 4100 PSI
MILLION CYCLE
                                                                                                                                   RECOMMENDED FOR:
High pressure hydraulic oil lines. Constant pressure (Isobaric) 280 bar / 4100 psi in all sizes. Small bend radius is an advantage in installations.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: EN 856 Type R12, EN 856 Type 4SP (size DN25, -16), ISO 18752-DC, SAE 100R12.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
Four (-06 to -24 size) and six (-32 size) alternating layers of spiralled high tensile steel wire.
COVER:
DIEHARDTM Black, oil and extra abrasion resistant synthetic rubber. Flame Resistant, Anti-Static (FRAS) & MSHA compliant. Highly visible layline branding for easy and permanent identification. No skiving required with T7000 Series Crimp Couplings.
FEATURES:
Tested to 1 million impulse cycles at up to 1/2 SAE 100R12 Minimum Bend Radius. Constant pressure 280 bar / 4100 psi in all sizes for easy system design and hose selection.
Small bend radius is an advantage in installations.
FRAS - FLAME RESISTANCE AND ANTI-STATIC:
DIEHARDTM complies with Flame Resistant and Electrical Resistance (Anti-Static) requirements of Australian Standard AS 2660 and Methods of Test AS 1180.10B and 13A.
Meets Flame Resistant Designation “U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
TEMPERATURE RANGE:
-40°C to +121°C, (-40°F to +250°F.)
For water, emulsions etc. see page 58.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
THIRD PARTY APPROVALS:
ABS, DNV-GL, LR, MED, USCG, GOST-R, BV, RINA and KR.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T7000 Series (sizes -06 to -32) pages 273 to 303. Assembly Instructions pages 478.
   H4000D – DIEHARD ISOBARIC SPIRAL HOSE
                        PART NO
  HOSE SIZE
  NOMINAL HOSE ID
    NOMINAL HOSE OD
 MAXIMUM WORKING PRESSURE
 MINIMUM BURST PRESSURE
  MINIMUM BEND RADIUS
 AVERAGE WEIGHT
 COUPLING SERIES
 ONE PIECE
          Hose
  DN
 Dash
 mm
 inch
mm
  inch
 bar
 psi
 bar
 psi
mm
  inch
 kg/m
 lb/ft
 NON-SKIVE
  H4006D
   10
  -06
  9,5
  3/8
 19,3
   0.76
  280
  4100
  1120
  16400
 60
   2.4
  0,61
  0.41
  T7000
 H4008D
  12
 -08
 12,7
 1/2
22,7
  0.89
 280
 4100
 1120
 16400
90
  3.5
 0,78
 0.52
 T7000
 H4010D
  16
 -10
 15,9
 5/8
24,9
  0.98
 280
 4100
 1120
 16400
100
  3.9
 0,76
 0.51
 T7000
 H4012D
  19
 -12
 19,1
 3/4
30,0
  1.18
 280
 4100
 1120
 16400
120
  4.7
 1,13
 0.76
 T7000
 H4016D
  25
 -16
 25,4
 1
36,9
  1.45
 280
 4100
 1120
 16400
150
  5.9
 1,60
 1.08
 T7000
 H4020D
  31
 -20
 31,8
 1.1/4
44,0
  1.73
 280
 4100
 1120
 16400
210
  8.3
 2,07
 1.39
 T7000
 H4024D
  38
 -24
 38,1
 1.1/2
50,8
  2.00
 280
 4100
 1120
 16400
330
  13.0
 2,65
 1.78
 T7000
 H4032D
    51
   -32
   50,8
   2
  66,4
    2.61
   280
   4100
   1120
   16400
  400
    15.8
   4,73
   3.18
   T7000
    Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
        HIGHER TECHCNOONLNOEGCYTEINQUGAPLASRGTNREARTSEHRIPPSERFORMANCE 75
TECHNICAL ADAPTORS COUPLINGS HOSE INTRODUCTION
   75   76   77   78   79