Page 78 - 2019 PRODUCT TECHNICAL MANUAL - HYDRAULICS V4-8
P. 78

 HOSE
ISOBARIC SPIRAL
 H4000S EXTREMELY ABRASION RESISTANT MSHA
ISOBARIC SPIRAL HOSE
280 BAR / 4100 PSI
MILLION CYCLE
      RECOMMENDED FOR:
High pressure hydraulic oil lines. Constant pressure (Isobaric) 280 bar / 4100 psi in all sizes. Small bend radius is an advantage in installations.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: EN 856 Type R12, EN 856 Type 4SP (size DN25, -16), ISO 18752-DC, SAE 100R12.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
Four (-06 to -24 size) and six (-32 size) alternating layers of spiralled high tensile steel wire.
COVER:
SLIDER Black, oil and extremely abrasion resistant synthetic rubber sheathed with a layer of extremely abrasion
resistant polyethylene. Flame Resistant, MSHA compliant. Highly visible layline branding for easy and permanent identification. No skiving required with T7000 Series Crimp Couplings.
FEATURES:
Tested to 1 million impulse cycles at up to 1/2 SAE 100R12 Minimum Bend Radius. Constant pressure 280 bar / 4100 psi in all sizes for easy system design and hose selection.
Small bend radius is an advantage in installations.
MSHA - FLAME RESISTANCE:
SLIDER complies with Flame Resistant requirements
of Australian Standard AS 2660 and Methods of Test
AS 1180.10B. Meets Flame Resistant Designation
“U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
TEMPERATURE RANGE:
-40°C to +121°C, (-40°F to +250°F.)
For water, emulsions etc. see page 58.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
THIRD PARTY APPROVALS:
ABS, DNV-GL, LR, MED, USCG, GOST-R, BV, RINA and KR.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T7000 Series (sizes -06 to -32) pages 274 to 304. Assembly Instructions pages 480.
 H4000S – SLIDER ISOBARIC SPIRAL HOSE
PART NO
HOSE SIZE
NOMINAL HOSE ID
NOMINAL HOSE OD
MAXIMUM WORKING PRESSURE
MINIMUM BURST PRESSURE
MINIMUM BEND RADIUS
AVERAGE WEIGHT
COUPLING SERIES
ONE PIECE
  Hose DN Dash mm inch mm inch bar psi bar psi mm inch kg/m lb/ft NON-SKIVE
 H4006S
10
-06
9,5
3/8
19,3
0.76
280
4100
1120
16400
60
2.4
0,61
0.41
 T7000
 H4008S 12 -08 12,7 1/2 22,7 0.89 280 4100 1120 16400 90 3.5 0,78 0.52
H4012S 19 -12 19,1 3/4 30,0 1.18 280 4100 1120 16400 120 4.7 1,13 0.76
H4020S 31 -20 31,8 1.1/4 44,0 1.73 280 4100 1120 16400 210 8.3 2,07 1.39
H4032S 51 -32 50,8 2 66,4 2.61 280 4100 1120 16400 400 15.8 4,73 3.18 Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
T7000 T7000 T7000 T7000
H4010S
16
-10
15,9
5/8
24,9
0.98
280
4100
1120
16400
100
3.9
0,76
0.51
T7000
H4016S
25
-16
25,4
1
36,9
1.45
280
4100
1120
16400
150
5.9
1,60
1.08
T7000
H4024S
38
-24
38,1
1.1/2
50,8
2.00
280
4100
1120
16400
330
13.0
2,65
1.78
T7000
      76 RYCO QUALITY
   76   77   78   79   80