Page 80 - 2019 PRODUCT TECHNICAL MANUAL - HYDRAULICS V4-8
P. 80

 HOSE
ISOBARIC SPIRAL
 H5000D EXTRA ABRASION RESISTANT FRAS
ISOBARIC SPIRAL HOSE
350 BAR / 5100 PSI
MILLION CYCLE
      RECOMMENDED FOR:
Very high pressure hydraulic oil lines. Constant pressure (Isobaric) 350 bar / 5100 psi in all sizes. Small bend radius is an advantage in installations.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: EN 856 Type R13, ISO 18752-CC, SAE 100R13.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
Four (-06 to -20 size) and six (-24 to -32 size) alternating layers of spiralled high tensile steel wire.
COVER:
DIEHARDTM Black, oil and extra abrasion resistant synthetic rubber. Flame Resistant, Anti-Static (FRAS) & MSHA compliant. Highly visible layline branding for easy and permanent identification. No skiving required with T6000 & T7000 Series Crimp Couplings.
FEATURES:
Tested to 1 million impulse cycles at up to 1/2 SAE 100R13 Minimum Bend Radius. Constant pressure 350 bar / 5100 psi in all sizes for easy system design and hose selection.
Small bend radius is an advantage in installations.
FRAS - FLAME RESISTANCE AND ANTI-STATIC:
DIEHARDTM complies with Flame Resistant and Electrical Resistance (Anti-Static) requirements of Australian Standard AS 2660 and Methods of Test AS 1180.10B and 13A.
Meets Flame Resistant Designation “U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
TEMPERATURE RANGE:
-40°C to +121°C, (-40°F to +250°F.)
For water, emulsions etc. see page 58.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
THIRD PARTY APPROVALS:
ABS, DNV-GL, LR, MED, USCG, GOST-R, BV, RINA and KR.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T7000 Series (sizes -06 to -24) pages 274 to 304. T6000 Series (size -12 to -32) pages 252 to 272. Assembly Instructions pages 480.
 H5000D – DIEHARD ISOBARIC SPIRAL HOSE
PART NO
HOSE SIZE
NOMINAL HOSE ID
NOMINAL HOSE OD
MAXIMUM WORKING PRESSURE
MINIMUM BURST PRESSURE
MINIMUM BEND RADIUS
AVERAGE WEIGHT
COUPLING SERIES
ONE PIECE
  Hose DN Dash mm inch mm inch bar psi bar psi mm inch kg/m lb/ft NON-SKIVE H5008D 12 -08 12,7 1/2 22,7 0.89 350 5100 1400 20400 90 3.5 0,78 0.52 T7000 H5012D 19 -12 19,1 3/4 29,6 1.17 350 5100 1400 20400 120 4.7 1,21 0.81 T6000 T7000 H5020D 31 -20 31,8 1.1/4 45,0 1.77 350 5100 1400 20400 210 8.3 2,42 1.63 T6000 T7000 H5032D 51 -32 50,8 2 67,5 2.66 350 5100 1400 20400 400 15.8 5,40 3.63 T6000
Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
 H5006D
10
-06
9,5
3/8
19,3
0.76
350
5100
1400
20400
60
2.4
0,61
0.41
  T7000
 H5010D
16
-10
15,9
5/8
26,2
1.03
350
5100
1400
20400
100
3.9
0,98
0.66
T7000
H5016D
25
-16
25,4
1
36,8
1.45
350
5100
1400
20400
150
5.9
1,72
1.16
T6000
T7000
H5024D
38
-24
38,1
1.1/2
52,7
2.07
350
5100
1400
20400
330
13.0
3,44
2.31
T6000
T7000
      78 RYCO QUALITY
   78   79   80   81   82