Page 81 - 2019 PRODUCT TECHNICAL MANUAL - HYDRAULICS V4-8

ISOBARIC SPIRAL
H5000S EXTREMELY ABRASION RESISTANT MSHA
ISOBARIC SPIRAL HOSE
350 BAR / 5100 PSI
MILLION CYCLE
RECOMMENDED FOR:
Very high pressure hydraulic oil lines. Constant pressure (Isobaric) 350 bar / 5100 psi in all sizes. Small bend radius is an advantage in installations.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: EN 856 Type R13, ISO 18752-CC, SAE 100R13.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
Four (-06 to -20 size) and six (-24 to -32 size) alternating layers of spiralled high tensile steel wire.
COVER:
SLIDER Black, oil and extremely abrasion resistant synthetic rubber sheathed with a layer of extremely abrasion
resistant polyethylene. Flame Resistant, MSHA compliant. Highly visible layline branding for easy and permanent identification. No skiving required with T6000 & T7000 Series Crimp Couplings.
FEATURES:
Tested to 1 million impulse cycles at up to 1/2 SAE 100R13 Minimum Bend Radius. Constant pressure 350 bar / 5100 psi in all sizes for easy system design and hose selection.
Small bend radius is an advantage in installations.
MSHA - FLAME RESISTANCE:
SLIDER complies with Flame Resistant requirements
of Australian Standard AS 2660 and Methods of Test
AS 1180.10B. Meets Flame Resistant Designation
“U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
TEMPERATURE RANGE:
-40°C to +121°C, (-40°F to +250°F.)
For water, emulsions etc. see page 58.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
THIRD PARTY APPROVALS:
ABS, DNV-GL, LR, MED, USCG, GOST-R, BV, RINA and KR.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T7000 Series (sizes -06 to -24) pages 274 to 304. T6000 Series (size -12 to -32) pages 252 to 272. Assembly Instructions pages 480.
H5000S – SLIDER ISOBARIC SPIRAL HOSE
PART NO
HOSE SIZE
NOMINAL HOSE ID
NOMINAL HOSE OD
MAXIMUM WORKING PRESSURE
MINIMUM BURST PRESSURE
MINIMUM BEND RADIUS
AVERAGE WEIGHT
COUPLING SERIES
ONE PIECE
Hose DN Dash mm inch mm inch bar psi bar psi mm inch kg/m lb/ft NON-SKIVE H5008S 12 -08 12,7 1/2 22,7 0.89 350 5100 1400 20400 90 3.5 0,78 0.52 T7000 H5012S 19 -12 19,1 3/4 29,6 1.17 350 5100 1400 20400 120 4.7 1,21 0.81 T6000 T7000 H5020S 31 -20 31,8 1.1/4 45,0 1.77 350 5100 1400 20400 210 8.3 2,42 1.63 T6000 T7000 H5032S 51 -32 50,8 2 67,5 2.66 350 5100 1400 20400 400 15.8 5,40 3.63 T6000
Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
H5006S
10
-06
9,5
3/8
19,3
0.76
350
5100
1400
20400
60
2.4
0,61
0.41
T7000
H5010S
16
-10
15,9
5/8
26,2
1.03
350
5100
1400
20400
100
3.9
0,98
0.66
T7000
H5016S
25
-16
25,4
1
36,8
1.45
350
5100
1400
20400
150
5.9
1,72
1.16
T6000
T7000
H5024S
38
-24
38,1
1.1/2
52,7
2.07
350
5100
1400
20400
330
13.0
3,44
2.31
T6000
T7000
HIGHER TECHCNOONLNOEGCYTEINQUGAPLASRGTNREARTSEHRIPPSERFORMANCE 79
TECHNICAL ADAPTORS COUPLINGS HOSE INTRODUCTION