Page 83 - 2019 PRODUCT TECHNICAL MANUAL - HYDRAULICS V4-8

RECOMMENDED FOR:
Extremely high pressure hydraulic oil lines. Constant pressure (Isobaric) 420 bar / 6100 psi in all sizes. Small bend radius is an advantage in installations.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: ISO 3862 Type R15, ISO 18752-CC, SAE 100R15.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
Four (-06 to -16 size), six (-20 to -24 size) and eight (-32 size) alternating layers of spiralled high tensile steel wire.
COVER:
SLIDER Black, oil and extremely abrasion resistant synthetic rubber sheathed with a layer of extremely abrasion
resistant polyethylene. Flame Resistant, MSHA compliant. Highly visible layline branding for easy and permanent identification. No skiving required with T6000 and T7000 Series Crimp Couplings.
FEATURES:
Tested to 1 million impulse cycles at up to 1/2 SAE 100R15 Minimum Bend Radius. World First: World’s first 2” (-32) hose tested to 1 million impulse cycles at 400mm (15.8”) Minimum Bend Radius. Constant pressure 420 bar / 6100 psi in all sizes for easy system design and hose selection. Small bend radius is an advantage in installations.
MSHA - FLAME RESISTANCE:
SLIDER complies with Flame Resistant requirements
of Australian Standard AS 2660 and Methods of Test
AS 1180.10B. Meets Flame Resistant Designation
“U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
TEMPERATURE RANGE:
-40°C to +121°C (-40°F to +250°F).
For water, emulsions etc. see page 58.
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
THIRD PARTY APPROVALS:
ABS, DNV-GL, LR, MED, USCG, GOST-R, BV, RINA and KR.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T7000 Series (sizes -06 to -20) pages 274 to 304. T6000 Series (size -12 to -32) pages 252 to 272. Assembly Instructions pages 480.
ISOBARIC SPIRAL
H6000S EXTREMELY ABRASION RESISTANT MSHA
ISOBARIC SPIRAL HOSE
420 BAR / 6100 PSI
MILLION CYCLE
H6000S – SLIDER ISOBARIC SPIRAL HOSE
PART NO
HOSE SIZE
NOMINAL HOSE ID
NOMINAL HOSE OD
MAXIMUM WORKING PRESSURE
MINIMUM BURST PRESSURE
MINIMUM BEND RADIUS
AVERAGE WEIGHT
COUPLING SERIES
ONE PIECE
Hose DN Dash mm inch mm inch bar psi bar psi mm inch kg/m lb/ft NON-SKIVE H6008S 12 -08 12,7 1/2 22,7 0.89 420 6100 1680 24400 100 3.9 0,78 0.52 T7000 H6012S 19 -12 19,1 3/4 30,6 1.20 420 6100 1680 24400 115 4.5 1,38 0.93 T6000 T7000 H6020S 31 -20 31,8 1.1/4 46,4 1.83 420 6100 1680 24400 220 8.7 2,97 2.00 T6000 T7000 H6032S 51 -32 50,8 2 71,5 2.81 420 6100 1680 24400 400 15.8 7,10 4.77 T6000
Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
H6006S
10
-06
9,5
3/8
19,3
0.76
420
6100
1680
24400
75
2.9
0,61
0.41
T7000
H6010S
16
-10
15,9
5/8
26,2
1.03
420
6100
1680
24400
110
4.3
1,00
0.67
T7000
H6016S
25
-16
25,4
1
37,5
1.48
420
6100
1680
24400
165
6.5
1,99
1.34
T6000
T7000
H6024S
38
-24
38,1
1.1/2
53,1
2.09
420
6100
1680
24400
350
13.8
3,81
2.56
T6000
CONNECTING PARTNERSHIPS 81
TECHNICAL ADAPTORS COUPLINGS HOSE INTRODUCTION