Page 86 - 2019 PRODUCT TECHNICAL MANUAL - HYDRAULICS V4-8

HOSE
BRAID
RECOMMENDED FOR:
High pressure hydraulic oil lines in applications where the outside cover of the hose is subjected to abrasion that may cause premature failure of standard hoses.
PERFORMANCE:
Meets or Exceeds the Performance Requirements of: EN 857 Type 1SC, ISO 11237 Type 1SC.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
One braid of high tensile steel wire.
COVER:
DIEHARDTM Black, oil and extra abrasion resistant synthetic rubber. Flame Resistant, Anti-Static (FRAS) & MSHA compliant. Highly visible layline branding for easy and permanent identification. No skiving required with T2000 Series Crimp Couplings.
FEATURES:
The very high abrasion resistant properties of the cover, combined with the high working pressures and excellent impulse life, results in increased service life and minimises equipment downtime.
FRAS - FLAME RESISTANCE AND ANTI-STATIC:
DIEHARDTM complies with Flame Resistant and Electrical Resistance (Anti-Static) requirements of Australian Standard AS 2660 and Methods of Test AS 1180.10B and 13A.
Meets Flame Resistant Designation “U.S MSHA” of the
US Department of Labour, Mine Safety and Health Administration.
TEMPERATURE RANGE:
From -40°C to +100°C (-40°F to +212°F).
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
THIRD PARTY APPROVALS:
ABS, DNV-GL, LR, MED, USCG, GOST-R, BV, RINA and KR.
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T2000 Series (sizes -04 to -16) pages 189 to 234. Assembly Instructions pages 480.
Not suitable for use with field attachable couplings.
DF1D
EXTRA ABRASION RESISTANT FRAS
COMPACT HOSE
ONE WIRE BRAID
DF1D - DINFLEX NON-SKIVE HOSE
PART NO
HOSE SIZE
NOMINAL HOSE ID
NOMINAL HOSE OD
MAXIMUM WORKING PRESSURE
MINIMUM BURST PRESSURE
MINIMUM BEND RADIUS
AVERAGE WEIGHT
COUPLING SERIES
ONE PIECE
Hose DN Dash mm inch mm inch bar psi bar psi mm inch kg/m lb/ft NON-SKIVE DF15D 8 -05 8,2 5/16 13,9 0.55 215 3100 860 12400 55 2.2 0,22 0.15 T2000 DF18D 12 -08 13,0 1/2 19,0 0.75 160 2300 640 9200 85 3.3 0,33 0.22 T2000
DF112D 19 -12 19,1 3/4 25,6 1.01 105 1500 420 6000 115 4.5 0,50 0.34 T2000 Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
DF14D
6
-04
6,6
1/4
12,2
0.48
225
3250
900
13000
50
2.0
0,20
0.13
T2000
DF16D
10
-06
9,8
3/8
15,6
0.61
180
2600
720
10400
65
2.6
0,26
0.17
T2000
DF110D
16
-10
16,2
5/8
22,2
0.80
130
1900
520
7600
100
3.9
0,44
0.30
T2000
DF116D
25
-16
25,4
1
33,6
1.32
90
1280
360
5120
150
5.9
0,75
0.50
T2000
84 RYCO QUALITY