Page 93 - 2019 PRODUCT TECHNICAL MANUAL - HYDRAULICS V4-8

RECOMMENDED FOR:
Extra high pressure hydraulic oil lines in applications where the hose cover is subjected to abrasion. Compact dimensions and small bend radius are advantages in installations where space is limited.
PERFORMANCE:
Exceeds the Performance Requirements of:
EN 857 Type 2SC, ISO 6805 Type 1 & Type 2, ISO 6805 Type 4 (sizes -10 and above), ISO 11237 Type 2SC.
CONSTRUCTION:
RYCO Proprietary DK2S design.
TUBE:
Black, oil resistant synthetic rubber.
REINFORCEMENT:
Two braids of high tensile steel wire.
COVER:
SLIDER Black, oil and extremely abrasion resistant synthetic rubber sheathed with a layer of extremely abrasion
resistant polyethylene. Flame Resistant, MSHA compliant. Highly visible layline branding for easy and permanent identification. No skiving required with T2000 Series Crimp Couplings.
FEATURES:
The extremely abrasion resistant properties of the cover, combined with the extra high working pressures and excellent impulse life, results in increased service life and minimises equipment downtime.
Compact dimensions and small bend radius are advantages in installations where space is limited.
MSHA - FLAME RESISTANCE:
SLIDER complies with Flame Resistant requirements
of Australian Standard AS 2660 and Methods of Test
AS 1180.10B. Meets Flame Resistant Designation
“U.S. MSHA” of the US Department of Labor, Mine Safety and Health Administration.
TEMPERATURE RANGE:
From -40°C to +100°C (-40°F to +212°F).
WORKING PRESSURE:
Maximum working pressures are based on 4:1 safety factor (maximum working pressure to minimum burst pressure).
COUPLINGS:
NON-SKIVE ONE-PIECE CRIMP
T2000 Series (sizes -04 to -20) pages 189 to 234. Assembly Instructions pages 480.
Not suitable for use with field attachable couplings.
BRAID
DK2S
EXTREMELY ABRASION RESISTANT EXTRA HIGH PRESSURE
COMPACT TWO WIRE BRAID HOSE
TESTED UP TO 1 MILLION CYCLES
DK2S - COMPACT EXTRA HIGH PRESSURE NON-SKIVE HOSE
NOMINAL HOSE ID
NOMINAL HOSE OD
MAXIMUM WORKING PRESSURE
MINIMUM BURST PRESSURE
MINIMUM BEND RADIUS
AVERAGE WEIGHT
COUPLING SERIES
PART NO
HOSE SIZE
ONE PIECE
Hose DN Dash mm inch mm inch bar psi bar psi mm inch kg/m lb/ft NON-SKIVE DK25S 8 -05 8,2 5/16 14,8 0.60 420 6100 1680 24400 60 2.4 0,36 0.24 T2000
DK24S
6
-04
6,7
1/4
13,7
0.54
450
6525
1800
26100
45
1.8
0,30
0.20
T2000
DK26S
10
-06
9,8
3/8
17,1
0.67
385
5590
1540
22360
70
2.8
0,41
0.27
T2000
DK28S 12 -08 13,0 1/2 20,3 0.80 345 5000 1380 20000 90 3.5 0,55 0.37
DK212S 19 -12 19,3 3/4 27,8 1.09 280 4100 1120 16400 160 6.3 0,88 0.59
DK220S 31 -20 32,2 1.1/4 43,5 1.71 175 2540 700 10160 280 11.0 1,70 1.14 Refer to the latest RYCO Crimp Charts for crimp diameter and mark lengths.
T2000 T2000 T2000
DK210S
16
-10
16,2
5/8
24,1
0.95
290
4210
1160
16840
130
5.1
0,69
0.46
T2000
DK216S
25
-16
25,8
1
35,6
1.40
200
2900
800
11600
210
8.3
1,31
0.88
T2000
HIGHER TECHCNOONLNOEGCYTEINQUGAPLASRGTNREARTSEHRIPPSERFORMANCE
91
TECHNICAL ADAPTORS COUPLINGS HOSE INTRODUCTION